Nationally AIM Compliant
Under 200 G/L
Excludes SCAQMD
PRODUCT SPECIFICATIONS
Restrictions: Apply when air and surface temperature are above 45 degrees & below 90 degrees
Weight Per Gallon: 8.9 pounds
Soilds by Weight: Approx. 66
VOC: Less Than 200 G/L
Paintable: No
Flashpoint: 105 degrees
Type: Semi-Transparent
Vehicle: Solvent
Finish: Satin
Colors: 6
Containers: 1 Gallon, 5 Gallon
Coverage: Approximately 200-400 square feet per gallon, depending on porosity of wood.
Dry Time: Approximately 24 to 48 hours depending on temperature, 30 days to full cure. All times are temperature and moisture dependent.
Clean-Up: Mineral Spirits
Application: Bristle brush, sprayer
Reduction: None
Cure: Air dry
Substrate: Wood
Log Siding Directions
DIRECTIONS: Wood should be clean and dry. Unseasoned wood should be allowed to dry to a moisture content of 12% to 15%. It is recommended that Rymar Rinseable Soap be used to clean wood before sealing. Washing with Rymar Rinseable Soap and sanding will help remove mill glaze for better adhesion. If using bleach on weathered logs, do not allow bleach to remain on the wood longer than five minutes. DO NOT USE METAL PAILS OR HARD WATER. Ask your dealer about preparing surfaces for coatings: they may be able to advise you otherwise depending on your situation. WHEN APPLIED TO THE EXTEREIOR ALL CRACKS MUST BE CAULKED AND LOG ENDS SUFFICIENTLY SEALED TO HELP PREVENT MOISTURE WICKING IN AND DAMAGING THE COATING. If there is more than one batch number, be sure to mix the batches together for color uniformity. Apply coating with a high quality bristle brush or by spraying and then back brushing. Brush with even strokes always going to a natural break such as a door, window or corner. If coating does not come out even on the first coat it is due to variations in penetration caused by vertical and horizontal wood grain. The second coat should even this out giving you a satin finish. If coating is still uneven a third coat may be needed. AT LEAST TWO COATS ARE NEEDED FOR BEST RESULTS. If a deeper color is desired additional coats may be applied. Dry time between coats is approximately 24 hours; reapplication must be done within 24 hours or when coating becomes tacky. Be sure to stir product through out entire period of application to prevent settling of pigment in the can.
NOTE! Do a test: Try a brushout on your project to ensure the color and product is what you want before doing your entire project.
PRODUCT SPECIFICATIONS
Restrictions: Apply when air and surface temperature are above 45 degrees & below 90 degrees
Weight Per Gallon: 8.9 pounds
Soilds by Weight: Approx. 65.7
VOC: Less Than 200 G/L
Paintable: No
Flashpoint: 105 degrees
Type: Clear
Vehicle: Solvent
Finish: Satin
Colors: Clear
Containers: 1 Gallon, 5 Gallon
Coverage: Approximately 200-400 square feet per gallon, depending on porosity of wood.
Dry Time: Approximately 24 to 48 hours depending on temperature, 30 days to full cure. All times are temperature and moisture dependent.
Clean-Up: Mineral Spirits
Application: Bristle brush, sprayer
Reduction: None
Cure: Air dry
Substrate: Wood
REFRESH DIRECTIONS
DIRECTIONS: Rymar Refresh is designed to be applied over existing weathered coatings to help bring back the new or just finished look. Wood should be clean and dry with a moisture content of 12% to 15%. It is recommender that Rymar Rinseable Soap be used to clean wood before sealing. If using bleach on weathered logs, do not allow bleach to remain on the wood longer than five minutes. DO NOT USE METAL PAILS OR HARD WATER. Ask your dealer about preparing surfaces for coatings: they may be able to advise you otherwise depending on your situation. WHEN APPLIED TO THE EXTEREIOR ALL CRACKS MUST BE CAULKED AND LOG ENDS SUFFICIENTLY SEALED TO HELP PREVENT MOISTURE WICKING IN AND DAMAGING THE COATING. If there is more than one batch number, be sure to mix the batches together. Apply coating with a high quality bristle brush or by spraying and then back brushing. Brush with even strokes always going to a natural break such as a door, window or corner. If coating does not come out even on the first coat it is due to variations in penetration caused by vertical and horizontal wood grain. If desired, a second coat may be applied to even this out giving you a satin finish. If coating is still uneven a third coat may be needed. Dry time between coats is approximately 24 hours; reapplication must be done within 24 hours or when coating becomes tacky. Be sure to stir product occasionally.
NOTE! Do a test: Refresh works on most oil and waterbase coatings. Try a brushout on your project to ensure the color and product is what you want before doing your entire project. When being applied over a coating deteriorated beyond a certain point substrate will darken considerably!
7740 CINNAMON LOG SIDING
